Wireless Video Transmission RF Frequency Digital Down Converter COFDM Transfer frequency 2.4G to 600Mhz low BDC

Digital Down Converter

Wireless Video Transmission RF Frequency Digital Down Converter COFDM Transfer frequency 2.4G to 600Mhz low

Очки Вузаны

1. Input frequencies from 24000 to 600MHz (Lower 1800Mhz)
2. High bandwidth
3. Low phase noise
4. High-frequency stability

Спецификация

RF Frequency Range: 2400 МГц
IF Frequency Range: 600 МГц
Return Loss:-12 дБ
Frequency Accuracy: ±10 ppm
Image Rejection: 60 ДБН
Flatness: ±0.5 dB (8MHz bandwidth)
Conversion Gain: 25 дБ
Phase Noise (dBc/Hz)
dBc/Hz@1KHz ≤-80
dBc/Hz@10KHz ≤-90
dBc/Hz@100KHz ≤-100
Питание Напряжение : 10~15V
Power Current: 100 маин
Operating Temperature Range: +25 ℃

 

Порт

RF IN: SMA-50K
IF OUT: SMA-50K
Power +12V: Stick
Музъем: Soldering lug

Валэктон

1. The converter does not need to add a low-noise amplifier at the back end.
2. Actual Test: closed-loop test under the frequency of 2.4GHz/bandwidth 4MHz, the receiving sensitivity can reach -105dBm.
3. Input frequency supports 1~3GHz. (We can help customize).
4. Output frequency supports 300~700MHz. (We can support customize).

About the above video:

Our most popular products are wireless video transmitters and receivers. Озьы, some clients require modification of the transmission frequency to meet local legal demand, in which case the digital frequency up-down converter block comes in handy. One customer requested that we customize the RF frequency down converter for his 2.4G wireless video transmitter. So the input frequency is 2.4GHz, the output frequency is 600MHz, and the lowdown frequency is 1800MHz. We created the sample in accordance with his specifications. So I showed him a simple video that showed the 2.4G transmitter and 600Mhz receiver working correctly. If you have a similar requirement, such as 1-3G frequency input and 300-700Mhz output, please contact us for a custom solution.

 

What is DDC

In digital signal processing, a digital down-converter (DDC) converts a digitized, band-limited signal to a lower frequency signal at a lower sampling rate in order to simplify the subsequent radio stages. The process preserves all the information in the original signal less that which is lost to rounding errors in the mathematical processes. The input and output signals can be real or complex samples. Often the DDC converts from the raw radio frequency or intermediate frequency down to a complex baseband signal.

Architecture

A DDC consists of three subcomponents: a direct digital synthesizer (DDS), a low-pass filter (LPF), and a down sampler (which may be integrated into the low-pass filter). The DDS generates a complex sinusoid at the intermediate frequency (IF). Multiplication of the intermediate frequency with the input signal creates images centered at the sum and difference frequency (which follows from the frequency-shifting properties of the Fourier transform). The low-pass filters pass the difference (i.e. baseband) frequency while rejecting the sum frequency image, resulting in a complex baseband representation of the original signal. Assuming a judicious choice of IF and LPF bandwidth, the complex baseband signal is mathematically equivalent to the original signal. In its new form, it can readily be down-sampled and is more convenient to many DSP algorithms. Any suitable low-pass filter can be used including FIR, IIR, and CIC filters. The most common choice is an FIR filter for low amounts of decimation (less than ten) or a CIC filter followed by an FIR filter for larger down-sampling ratios.

Variations on the DDC

Several variations on the DDC are helpful, including many that input a feedback signal into the DDS. These include:

1. Decision-directed carrier recovery phase-locked loops in which the I and Q are compared to the nearest ideal constellation point of a PSK signal, and the resulting error signal is filtered and fed back into the DDS
2. A Costas loop in which the I and Q are multiplied and low pass filtered as part of a BPSK/QPSK carrier recovery loop

Implementation
DDCs are most commonly implemented in logic in field-programmable gate arrays or application-specific integrated circuits. While software implementations are also possible, operations in the DDS, multipliers, and input stages of the low-pass filters all run at the sampling rate of the input data. This data is commonly taken directly from analog to digital converters (ADCs) sampling at tens or hundreds of MHz. CORDIC is an alternative to the use of multipliers in the implementation of digital down converters.

Here is a client’s customized project, 1300~1400 Mhz input down converter to 300-400Mhz.

图传下变频器中国深圳供应商， 频率定制

名称: 图传下变频器
型号: LWDC-248258I
编号: 1805001
RF +12V IF
Нимыз: RF Down Converter
Котельников: LWDC-3000I
Котельников: LWDC-1400
Frequency input 2G~2.7G(2000~2700Mhz)
Lower: 1800МГц
Frequency output: 200Mhz-700Mhz
SN2405002

	MIN	TYPE	MAX
Operating frequency band (МГц)	1300	–	1400	工作频段 （MHz)
Local oscillator (МГц)		1000		本振（MHz)
Intermediate frequency (МГц)	300	–	400	中频（MHz)
Conversion gain Gain(дБ)	18	20	22	变频增益Gain(дБ)
Gain Flatness (дБ)		±1	–	增益平坦度(dB）
Noise figure (дБ)		1.5	–	噪声系数(dB）
Port Standing Wave Ratio VSWR	1.5	1.8	2	端口驻波比VSWR
Port Impedance(ом)		50	–	端口阻抗(ом)
Maximum input power (дБм)		-5		最大输入功率（dBm）
Maximum output power (дБм)		15		最大输出功率（dBm)
Working voltage (- Ын)	10	12	15	工作电压（V)
Ток ужасьёс (маин)	130	150	180	工作电流（mA）
Температура ужасьёс (°C)	-25		55	工作温度（°C)
Температура возёно (°C)	-45		65	存储温度（C)
Dimension mm (without connectors)		62x32x14mm		尺寸 mm (不含连接器)

Customize Frequency Specification Sheet Download

OF 1750Mhz Down

Item	Параметръёсты
input frequency	2100 MHz ～2500 MHz
output frequency	350 MHz ～750 MHz
Local frequency	1750 МГц
Куара Коэффициентъёс	≤1.5dB
gain	15 дБ
Carrier leakage	≤-20dBm
Belt unevenness(8МГц)	≤1.5dB
IIP3:	≥15dBm
maximum input level	0дБм
VSWR	≤1.5
operation temperature	-10～+60℃
voltage current	≤12V/240mA
RF Interface	N-50KFD
Быдӟалаез	108*48*22мм
Power supply mode	Online power supply